range Technical inspection
Filters
Category
Vehicle types
Installation types
Standard side slip tester without release plate
The 44100 side slip tester range provides optimum control of the measurement of a vehicle’s slip as it passes over the plate. This operation is the first step in checking the vehicle’s geometry during a vehicle inspection test.
The slip value obtained is used to measure the trajectory deviation of a vehicle axle. This measurement is expressed in m/km or mm/m.
Wide side slip tester with release plate
The 44100 side slip tester range provides optimum control of the measurement of a vehicle’s slip as it passes over the plate. This operation is the first step in checking the vehicle’s geometry during a vehicle inspection test.
The slip value obtained is used to measure the trajectory deviation of a vehicle axle. This measurement is expressed in m/km or mm/m.
Wide side slip tester without release plate
The 44100 side slip tester range provides optimum control of the measurement of a vehicle’s slip as it passes over the plate. This operation is the first step in checking the vehicle’s geometry during a vehicle inspection test.
The slip value obtained is used to measure the trajectory deviation of a vehicle axle. This measurement is expressed in m/km or mm/m.
4-post lift alignment lifts with integrated auxiliary lift 5,0 T, platform mength 5280 mm
Our 4-post lifts, QUADRA552LA, combine workmanship quality with a perfect design and advanced technology. Equipped for geometry with auxiliary lift, the QUADRA552LA can accommodate all types of light vehicles and most commercial vehicles, increasing your profitability.
4-post lift alignment lifts with integrated auxiliary lift 5,0 T, platform mength 5780 mm
As the QUADRA552LA, the QUADRA558LA also features a perfect finish. Hoses and wires from command unit to the runways, are routed into a plastic articulated chain providing also better reliability.
The QUADRA558LA, features longer runways than the QUADRA522LA, it allows working on vehicles with longer wheelbases.
The integrated auxiliary wheel-free offers adjustable lifting platforms – with front and rear extensions – to fit every vehicles.
Scissor lift 5,0 T with lifting runways and auxiliary wheel-free lift
The GALAXIE551ELA is a 5T scissor lift with long runways (main lift) and under body lift (auxiliary lift).
Recessed in a pit, the flush mounted runways can accommodate vehicles with very low ground clearance.
This flushed mounted configuration saves space in the workshop.
Optional long drive-in ramps allow above ground installation (without the need of a pit), if required.
Scissor lift 5,0 T with lifting runways and auxiliary wheel-free lift and play detectors
This scissor lift GALAXIE551ECT, is especially designed to meet vehicle inspection requirement, meets all expectations of ourcustomers.
Thanks to a lifting capacity of 5T and extra long runways 5,10 m, the GALAXIE551ECT can accomodate to almost all, including commercial vans and motorhome.
A super fast raising time is provided thanks to the use of two hydraulic groups working simultaneously.
Motorcycle lift for vehicle inspection – Vehicle categories L1, L3
Ultimate lifting solution to cover any requirement in vehicle inspection (european category L).
This lift features an electro-hydraulic drive system, with power pack located in themobile command unit, providing smooth,silent, and quick working operations (raising time : 30 seconds).
The space saving configuration allows perfect access all around the lift to the vehicle, with the possibility for the inspector to stand verynear to raised vehicle. This specification is ideal for vehicle inspection activities.
Manual headlight tester
This headlight tester measures and checks all types of headlights. It incorporates electronics for automatic data transfer with Bilanmatic®.
Robotic headlight tester
This robotic headlight tester allows automatic inspection without any manipulation of headlights.
Headlight tester
Device dedicated to measure high / low beams and fog lights :
• Analysis by CMOS camera ton control the latest generation of lights : Xenon, Halogen, LED
• Wide 7“ colour touch screen
Headlight tester
Device dedicated to measure high / low beams and fog lights :
• Analysis by CMOS camera ton control the latest generation of lights : Xenon, Halogen, LED
• Wide 7“ colour touch screen
Sound level meter class 1
The SONO-C1 sound level meter is designed for use with all types of noise measurement applications.
The device comes with 10 metres of cable and a tripod for conducting exhaust noise measurements at a distance from its processing unit. The Class 1 solution complies with standard IEC 61672 and guarantees data acquisition with impeccable metrological quality. With its multitask design, it concentrates high-performance and simplicity in a single device. It also features a high-definition, sunlight viewable colour display.