3,0 T mid-raise wheel free lift
This electro-hydraulic lift features a lifting height of 1000 mm, perfectly adapted to bodywork and works around the wheels.
Anchoring is not required (thus possible). The lift is movable (when unloaded) by the mean of its mobility kit supplied with the lift as standard.
Low profile design (min. height only 105 mm).
The access ramps can be positioned at a horizontal position, providing a lifting platform extension, front and rear. Thus, the lifting platform length can be adjusted from 1420 mm to 2028 mm, making the lift suitable to raise short and long wheelbase vehicles, as well as many commercial vehicles and vans.
Hydraulic oil
4x rubber lifting pads
Mobility kit
This electro-hydraulic lift features a lifting height of 1000 mm, perfectly adapted to bodywork and works around the wheels.
Anchoring is not required (thus possible). The lift is movable (when unloaded) by the mean of its mobility kit supplied with the lift as standard.
Low profile design (min. height only 105 mm).
The access ramps can be positioned at a horizontal position, providing a lifting platform extension, front and rear. Thus, the lifting platform length can be adjusted from 1420 mm to 2028 mm, making the lift suitable to raise short and long wheelbase vehicles, as well as many commercial vehicles and vans.
Size (in mm) :
Parcel Nr.1 : 2005 x 1880 x 300 mm
Parcel Nr.2 : 1150 x 540 x 430 mm
Weight (en kg):
Parcel Nr.1 : 420 kg
Parcel Nr.2 : 54 kg
| TECHNICAL DATA | ARGOS30M |
|---|---|
| Lifting capacity | 3,0 t |
| Mid-raise lift | yes |
| Double scissor lift | – |
| Movable (not loaded) | oui |
| Lifting/lowering time | 30 / 30 sec. |
| Dimensions (at lowest position) (L x w x h) | 2028 x 1995 x 105 mm |
| Min. height | 105 mm |
| Max. lifting height | 1000 mm |
| Platform length | 1420 – 2028 mm |
| Platform width | 460 mm |
| Free space between the platforms | 860 mm |
| Power supply | 230 V / 1 ph / 50 Hz / 20 A / 2,2 kW |
| Air supply | – |
2,0 T jacking beams without running wheels
Universal and indispensable solution for jacking under axle.
This jacking beams 2,0 T is designated to run between the two platforms of the lift, or in a pit, to be positioned exactly under the vehicle’s axle to be raised.
The lifting movement is done by an hydraulic lifting cylinder, with oil pressure created by an air-hydraulic motor integrated in the jacking beam. The jacking beam is only air supplied (no power), and features safety latching and savety overloading devices. The lowering movement requires two hands for safety reason, with a “hold to run” command.
2,6 T jacking beam without running wheels
Universal and indispensable solution for jacking under axle.
This jacking beams 2,6 T is designated to run between the two platforms of the lift, or in a pit, to be positioned exactly under the vehicle’s axle to be raised.
The lifting movement is done by an hydraulic lifting cylinder, with oil pressure created by an air-hydraulic motor integrated in the jacking beam. The jacking beam is only air supplied (no power), and features safety latching and savety overloading devices. The lowering movement requires two hands for safety reason, with a “hold to run” command.
Double scissor low profile lift 3,0 T
This electro-hydraulic wheel free lift, features a lifting height of 1900 mm, providing optimal access to the vehicle underbody for repair or service works.
Set 8 universal adaptators
Compatible with vehicle lifting 4619316
Set, 8 universal adaptors, with oblong fixing hole for continuous and accurate position adjustment. The adaptor gets quickly and safely clamped onto the lifting platform, thanks to its thumb screw, to be hand tightened thumb screw.
Lifting table – 1200 kg
This lifting table has been especially designed to easily and safely remove and install heavy batteries from electric vehicles, in conjunction with the use of a 2-post lift such as the Azur42AH.
Photocell for installation under low ceiling
Compatible with 2-post lifts AZUR35CH, AZUR42CH, AZUR50CH and AZUR50WH